Teledyne Microwave Solutions

Support

Standard Synthesizers

Teledyne Microwave Solutions has long been a trusted industry supplier of advanced Synthesizers, Converters and Transceivers. TMS's Frequency Synthesizers are available from the very complex dual loop frequency synthesizer to more simple phase locked loop designs, supporting a number of communication bands from L-Band through Ka-Band.

TMS SYNTHESIZER PRODUCTS-AT-A-GLANCE

Synthesizer

  • SPOTLIGHT: The Advanced Single Loop Frequency Synthesizer (see below)
  • State of the art phase noise performance
  • Tuning speed in nanoseconds
  • Broadband Tuning Range: L to K band
  • SRAs, IMAs, MFM, IFM, LRU
  • Very low SWaP (Size, Weight and Power)
  • DDS in the Loop

Explore TMS Synthesizers

MARKETS & APPLICATIONS

  • Microwave radio system
  • Satcom converters
  • EW (Electronic Warfare)
  • Test equipment
  • Exciters
  • Jammers
  • Military communication systems 

 

Converters

TMS offers broadband IMA modules for both block conversion and digitally tuned conversion applications. Drawing upon a large design library of broadband thin film circuits, TMS can provide custom state of the art solutions for multi-octave applications for up and/or down conversion.

TMS CONVERTERS AT-A-GLANCE

Small-Signal-Amplifier

  • SPOTLIGHT: Common Data Link Subsystem: 10W Up/Down Converter Ku to S Band (See below)
  • 2 to 18 GHz RF range
  • 1 to 2 GHz IF range
  • Very high power front end protection (>500W pulsed)
  • Tuned response with 1Hz resolution
  • Tuned response times of less than 1uS
  • Wideband input dynamic ranges of >60dB
  • -45dBc spurious

Explore TMS Converters

KEY FEATURES

Designed for airborne military environments in hermetically sealed packages, TMS converters meet system requirements under the most severe environmental conditions.

Transceivers

Transceiver units simultaneously receive and transmit radio frequency (RF) signals with carrier frequencies over multiple octaves from 500 MHz to 40 GHz and IF instantaneous bandwidths (IBW) of 500MHz.

TMS TRANSCEIVER PRODUCTS-AT-A-GLANCE

TMS Tranceivers-2

  • Frequency Range 0.75 GHz -18.25 GHz
  • IF range of 1-2GHz with 500MHz IBW
  • Dual conversion with Switch Filter pre-selection
  • Wide Dynamic Range +5 dB to -65 dB
  • Low NF of typically <10 dB
  • <-60 dBc Spur Performance over full frequency range
  • Integrated SDLVA & LO Generator
  • Fast tuned LO with frequency switching speed of <100 nSec
  • Frequency memory
  • Package Size 4.25 “ x 2.25”x 7”

Explore TMS Transceivers

APPLICATIONS

  • Electronic Countermeasures (ECM)
  • Electronic Support Measures (ESM)
  • SIGINT/ELINT/FISINT/COMINT
  • Radar Warning Receivers
  • Missile Warning Receivers

Multi-function Assemblies

DownloadEWCapBroMulti-function assemblies including DIFM, SDLVA, Channelisers, Converters, Local Oscillators, Switched Multiplexers.

 

 

Cougar Custom Integrated Assemblies

Cougar offers full first-level integration capabilities, providing not just performance components but also full subsystem solutions to help reduce program schedule and cost. Drawing on our expanding breadth of components, Cougar delivers customer-specified subsystems of analog and mixed analog-digital design, including hybrid, MMIC, and mixed hybrid-MMIC configurations. Designed to meet military or space applications, some typical subsystems Cougar delivers include I/Q demodulators, coupled detector assemblies, switched amplifier detector assemblies, and dual-band VCOs.

Our experienced component and subsystem engineering staffs work closely with the customer's design team. We can help identify and develop the correct integrated subassembly to complete the system requirements and reduce component interface difficulties. Following are several examples of our integrated subassemblies.


X Band Limiting Amplifier

XBANDOUT2winset

Replacing an older design, Cougar reduced component count and increased overall reliability in this X-band limiting amplifier. The design covers 9.0 to 10.0 GHz and provides dynamic range over inputs from -14.0 to -4.0 dBm, and output of +28.5 dBm. The output power variation versus frequency and temperature (-46° to 72° C) is ~±0.3 dB and typical rise and fall times are ~5 nanoseconds. The amplifier operates from a 400 Hz, 115 Vac power source. Cougar can also provide limiting amplifiers covering broader frequency ranges, dynamic ranges, and output powers in excess of 1 watt.

  • 9 to 10 GHz Frequency
  • +28.5 dBm Output Power
  • ±0.3 Output Power Change Vs. Frequency and Temperature
  • (-46° to 72° C)
  • Operates off 400 Hz 115 VAC Supply

Low Noise Dual Band VCO

LONoiseDualBandps

This custom oscillator subassembly consists of two low noise oscillators covering 1.5 to 2.5 GHz, a power combiner, a standard Cougar amplifier, and a lowpass microstrip filter. Cougar designed both oscillators for low phase noise and linear tuning. The output frequency bands are switched using standard TTL control.

  • Frequency Output 1500 to 2500 MHz in Two Bands
  • +3 to +8 dBm Output Power
  • < 2 dB Output Power Flatness
  • Excellent Phase Noise
  • Offset dBc/Hz
    • 10 kHz -86
    • 100 kHz -114
    • 1 MHz -135
    • 10 MHz -158
    • 100 MHz -160

IQ Demodulator

IQDEMODsilveps

Cougar's IQ Demodulators are fully space-qualified designs providing stringent phase and amplitude matching, and superior output third order intercept performance. To meet high LO and IF rejection requirements Cougar uses a diplexer at the I and Q ports. All components and processing fully meet MIL-PRF-38534, Class K and MIL-DTL-28837. Cougar can provide performance to meet most receiver system requirements, including single or moving LO frequencies and tight phase and amplitude matching. Customers can specify our designs for space, military, or commercial applications.


Switched Limiting Amp with Detected Output

SwitchampLimiting amplifier sets dynamic range from -10.0 to -5.0 dBm input to 2.0 dBm output. TTL controlled, fast switching and high isolation 10 dB On-to-Off, and includes internal filtering for improved harmonic performance. Analog detector monitored output, or dual RF outputs.

  • Operates at 3.6 GHz
  • -8 to -3 dBm Input Power to +2 to +5 dBm Output Power
  • Amplitude and Phase Matched Dual Outputs (±0./2 dB, ±1°)
  • TTL Compatible, 70 dB On-to-Off Ratio, 50 h S Response Integrated RF Switch

Switch Amp

LimiterSwtchAmpps

One of many potential designs, Cougar's switched amplifier covers 100 to 2000 MHz, providing 18 dB gain, phase matched to within ±1.0 degree.

The primary RF input and a secondary calibration signal input are switched, then amplified, and split to two outputs. Gain balance between any of the two outputs is ± 0.5 dB. Output power at 1 dB compression is +14 dBm and input/output VSWR is 2.0:1 maximum.


Ku Band Gain Control Amplifier

CCM2096

Expanding Cougar's existing line of high frequency amplifiers, Cougar offers microwave gain controllable amplifiers designed and biased for critical performance applications. One example covers 10-13 GHz, offers 45 dB unattenuated small signal gain with 15 dB attenuation range. Typical gain flatness is ±0.5 dB, +35 dBm third order intercept point, +22 dBm minimum 1-dB gain compression, and 3.5 dB unattenuated noise figure 4.5 dB at full attenuation. This is only one of a series of microwave controllable amplifiers currently in production.

  • 10 to 13 GHz Frequency Band
  • 45 dB Unattenuated Gain
  • ± 0.5 dB Gain Flatness
  • 3.5 dB Noise Figure (at unattenuated setting, 4.5 dB full attenuation)
  • 15 dB Attenuation Range
  • +22 dBm Output Power at 1dB Compression
  • +35 dBm Third Order Intercept Point

Voltage Controlled Oscillator Assembly with Heater

InsideCCM560

Cougar has designed a Voltage Controlled Oscillator to replace an existing application. The oscillator covers the 520 to 560 MHz frequency range. The oscillator provides +10 to +13 dBm output power. The oscillator has internal heaters designed to maintain the oscillator assembly at constant temperature. The unit operates over the 0° to 60° C temperature range with ~200 KHz frequency variation due to temperature variation.

  • 520 to 560 MHz Frequency Output
  • <±0.2 MHz Frequency Drift (0° to 60° C, internal heater to stabilize Frequency Output)
  • +10 to +13 dBm Output Power
  • Settles to within 0.5 MHz in less than 25 ηSec.

 X Band Coupler with Dual Output Threshold Detector

XBANDCOUPLER1

The X Band coupler with dual output has an input power range of either -5 to +10 dBm, or +5 to +20 dBm. Covering 8.0 to 9.5 GHz, insertion loss is less than 1.0 dB and VSWR is 1.5:1. The coupler/detector has two external resistors providing independently settable threshold TTL outputs. The power flatness is ~0.4 dB and hysteresis is 0.1 dB. Cougar can provide this function in other frequency ranges and input power ranges.

  • 8 to 10 GHz Operational Frequency
  • <1.0 dB Insertion Loss
  • Two Independently Settable (external resistor) Threshold Detector Outputs
  • High Speed Threshold Detector Response (<80 ηSec)

Switched Amplifier with Analog Detector Output

  • Operates at 3 GHz
  • -10 to -5 dBm Input Power to +4 to +7 Output power
  • Analog Detector Output
  • TTL Compatible, 70 dB On-to-Off Ratio, 50 ηSec Response Integrated RF Switch

Low Noise Triple Band Voltage Controlled Oscillator

CCM4701This Low Noise Triple Band Voltage Controlled Oscillator was designed to meet a specific customer requirement. The VCO cover the 3300 to 4700 MHz frequency range in three bands. The output power is +9 to +12 dBm with an integrated buffer amplifier to minimize load pulling. The three bands are selected using standard TTL control.

  • Frequency Output 3300 to 4700 MHz in Three Bands
  • +9 to +12 dBm Output Power
  • Excellent Phase Noise
  • Offset dBc/Hz
  • 10 kHz -80
  • 100 kHz -105
  • 1 MHz -125
  • 10 MHz -145

Five Channel Amplifier

5channelCougar designed the Five Channel Amplifier specifically for a custom space application. Each independent channel used dedicated RF Input/Output and DC bias connections. Cougar tailored each channel's RF performance differently to meet the application requirements. Cougar manufactured and screened all components per MIL-PRF-38534, Class K. Additionally, to meet mission requirements Cougar tested the top assembly for RF and DC parameters during MIL-STD-202 thermal cycling and random vibration environments. This effort required disciplined development, manufacturing and program management efforts to meet challenging mechanical and RF engineering requirements.


VHF Band 1.0 Watt Amplifier with RF Bypass

VHFBandCougar has developed a 35 to 350 MHz custom amplifier with 1 watt output power. The amplifier has 29 dB gain with 3 dB noise figure. The amplifier assembly has a RF switch so that the RF input can be connected directly to the output bypassing the amplifier. The amplifier goes into the "bypass" state when the DC bias is removed from the switch. This unit is one of a series of amplifiers that covers the 1 MHz to 2100 MHz with similar operation.

  • 35 to 530 MHz
  • 30 dB Gain
  • 3 dB Noise Figure
  • 1 Watt Output Power
  • Amplifier/Bypass Selectable
  • Power Off Bypass Operation
  • Gain and Phase matched (Unit-to-Unit)

3072 MHz Limiting Amplifier

The CCM3072 is single input three output limiting amplifier operating at 3072 MHz. The input power range is from -10 to 0 dBm with an output at +7 dBm and two at +1 dBm. The output power change due input power range, temperature (-20° to 85° C) and voltage variation is ~ +/-0.8 dB. Input and output VSWR are all <1.2:1. Incorporated into the design is a narrow band pass filter between the amplifiers and power splitter to reject spurious input signals and reduce harmonic outputs. This limiting amplifier is being built for stringent space applications.


2 to 18 GHz 6 Channel Downconverter

6Channel6Teledyne Cougar's Six Channel 2 - 18 GHz (RF and LO) downconverter operates with an IF of ~960 MHz, providing 25 dB of RF-IF gain, and bandwidth of ~500 MHz. This downconverter operates on a single LO at -6 dBm which is amplified, split, then again amplified to each of the 6 channels. Integrated into each channel is a range extension switch, controlled by a TTL input and adding 20 dB attenuation. Noise figure is ~ 13.5 dB and output IP3 is ~+25 dBm. The downconverter is 2- sided, hermetically sealed and designed for rugged applications.


 

17 to 19 GHz QPSK Modulator

QPSKModulatorThe CCM19001 is a Differential Drive Digital QPSK (Quadrature Phase Shift Keying) modulator operating across the 17.0 to 19.0 GHz frequency range. The modulator utilizes differential drive digital inputs (180º apart) to drive both of the bi-phase modulators (mixers) integrated into the assembly. The modulator is a combination of a matched pair bi-phase modulators, which are in quadrature (90º) to each other. It is modulated by switching polarities of the DC voltage controls in 4 different logic states ("0,0", "0,1", "1,0" & "1,1") for 4 phase states. The QPSK modulator provides constant amplitude, 90º vector: 0 (ref.), 90º, 180º, 270º and operates across the -55º to 85º C temperature range.


CCM1095 and CCM2096 - 3 to 5 Watt Power Amplifiers

CCM2096The CCM1095 and CCM2096 are power amplifier that use current efficient Silicon Carbide output semi-conductors to achieve +35 to +38 dBm output power. An internal sequencing circuit is included to provide for safe operation of the output power device.

The CCM1095 can be adjusted to operate at voltages from +28 to +42 volts. The bias current can be adjusted to operate at any of the voltages mentioned from 250 to 600 mA. The voltages used and current settings are a function of the output power requirements.

The CCM1095 provides +37 dBm with 36 volts and 500 mA of current. The CCM2096 delivers +36 dBm output power with 36 volts and 500 mA on the output stage. The driver stage is operated with +15 volts and draws 450 mA.

The housing shown includes the RF amplifier and the voltage sequencer. It provides over 15 sq. inches of mounting surface area to maintain cool operation.

Click the image to view the pdf

CCM 1095
CCM1095chart

 CCM 2096
CCM2096chart

 


 
Teledyne Microwave Solutions  |  11361 Sunrise Park Drive, Rancho Cordova, CA 95742

Phone: (800) 832-6869  |  © 2017 Teledyne Microwave Solutions. All rights reserved.